Attwood Stainless Steel Scupper Valves Uživatelský manuál stáhnout pdf

Attwood

A Steelcase Company

1016 N. Monroe Street, Lowell, MI 49331-0260

Threaded Thru-Hulls

and Scupper Valve

Installation Instructions

66558 - 66567 Series

SAVE THESE INSTRUCTIONS

Form Number 69398 Rev A 03-07

These stainless steel products carry a Limited Lifetime warranty.

WARNING:

Read instructions carefully before installing and using this product. To

prevent injury, remove boat from water when installing this product and

before using 120V power tools.

The stainless steel thru-hull and scupper valve must be mounted above

the boat’s maximum water line as determined by the boat’s draft at the

maximum loading recommended by the boat manufacturer. On sailboats,

mount high enough on the center of the transom so fitting is above water

line at all times.

FEATURES

The stainless steel thru-hull and scupper valve have threaded ends. A

seacock or in-line valve can be threaded directly onto these fittings. See

chart below to match thread size.

REQUIRED FOR INSTALLATION

• Expandable wrench (max. 2-1/2", 64mm)

• Hole saw (see chart for size)

• Cordless drill

• Polyurethane marine sealant

Thru-Hull Thread Thread Hole Saw

Part Number Size (NPSM) Length Size

66558 1/2" 2-1/8" 7/8"

66559 3/4" 2-1/8" 1-1/8"

66561 1" 2-1/4" 1-3/8"

66562 1-1/4" 2-1/2" 1-3/4"

66563 1-1/2" 2-3/8" 2"

66564 2" 2-1/2" 2-1/2"

Scupper Valve

Part Number

66565 1-1/2" 3-1/2" 2"

66567 2" 2-1/2" 2-1/2"

THRU-HULL INSTALLATION

Mount thru-hull in the transom or side of hull, at least 12" (30cm) above

maximum water line. If possible, place fitting on the same side as the

steering wheel so driver can see discharge of water when the pump is

working properly.

1. Use a hole saw (see chart for size – check against thru-hull) to cut

hole in the transom or hull. (Figure 1)

2. Remove tightening nut. Apply a small bead of marine sealant in the

groove under the flange.

3. Place thru-hull into the hole. After this point, all connections may be

made from inside the hull.

4. Place tightening nut onto threads, with wide side toward hull. Tighten

firmly, but do not damage gelcoat by over-tightening. To prevent

turning, grip wrench flats with an expandable wrench.

5. Turn seacock onto the thru-hull threads. Grip the wrench flats to hold

thru-hull in place.

6. Lead hose from bilge pump to seacock at an upward angle. Fasten

tightly at both ends with hose clamps.

SCUPPER VALVE INSTALLATION

The Attwood threaded scupper valve is designed for boats with a

self-bailing cockpit. The flapper valve opens outward to release water

and automatically closes to help prevent backwash from entering the

cockpit. Mount scupper in the transom at least 12" (30cm) above

maximum water line.

1. Use a hole saw (see chart in left column for size – check against

scupper) to cut hole in the transom or hull. (See Figure 2.)

2. Remove tightening nut. Apply a small bead of marine sealant in the

groove under the flange.

3. Place scupper into the hole. After this point, all connections may be

made from inside the hull.

4. Place tightening nut onto threads, with wide side toward hull. Tighten

firmly, but do not damage gelcoat by over-tightening. To prevent

turning, grip wrench flats with an expandable wrench.

5. Turn seacock onto the scupper valve threads. Grip the wrench flats

to hold scupper in place.

6. Lead hose from cockpit to seacock at a downward angle. Fasten

tightly at both ends with hose clamps.

Figure 1

Figure 2

Cockpit

Cockpit Drain (#3882-1)

Scupper Valve

At Least 12" Above

Maximum Water Line

Marine Sealant

Seacock

Wrench Flats

Hose

Clamps

Hose

ATTWOOD LIMITED LIFETIME WARRANTY

ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan 49331

(“Attwood”) warrants to the original consumer purchaser that, under normal use

and service, this Attwood brand product will be free from defects in materials and

workmanship for the service life of the vessel on which it is originally installed.

This limited warranty is not applicable if the product has been damaged by accident,

improper installation, unreasonable or improper use, lack of proper maintenance,

unauthorized repairs or modifications, normal wear and tear, or other causes not

arising out of defects in materials or workmanship. Attwood products are warranted

for use on pleasure boats. Any other use — including but not limited to commercial,

racing, or non-marine use — are not covered under this warranty. Attwood’s

obligation under this warranty is limited to repair of the product at Attwood’s plant

or replacement of the products at Attwood’s option without expense to the original

consumer purchaser. Any expenses involved in the removal, reinstallation or

transportation of the product are not covered by this warranty. The product must

be returned to Attwood’s plant at the address above, postage prepaid, and insured

with proof of original purchase including date. If Attwood is unable to replace the

product and repair is not commercially practical or cannot be timely made, or if

the original consumer purchaser is willing to accept a refund in lieu of repair or

replacement, Attwood may refund the purchase price, less an amount for depreciation.

The acceptance by Attwood of any product returned or any refund provided by

Attwood shall not be deemed an admission that the product is defective or in

violation of any warranty. Products that are replaced or for which a refund is

issued become the property of Attwood.

THIS WARRANTY IS ATTWOOD’S ONLY EXPRESS WARRANTY OF THIS

PRODUCT. NO IMPLIED WARRANTY SHALL EXTEND BEYOND ONE (1)

YEAR FROM THE DATE OF ORIGINAL CONSUMER PURCHASE. ATTWOOD

SHALL NOT BE LIABLE FOR ANY DAMAGES, FOR LOSS OF USE OF THIS

PRODUCT, NOR FOR ANY OTHER INCIDENTAL OR CONSEQUENTIAL

DAMAGES, COSTS OR EXPENSES.

Some states do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitations and exclusions may not apply to you. This

warranty gives you specific legal rights, and you may have other rights which

vary from state to state.

Hose

Clamps

Marine Sealant

Seacock

Thru-Hull

Wrench

Flats

Hose at Upward Angle

At Least 12" Above

Maximum Water Line

1 2 3

Shrnutí obsahu

Strany 1 - Installation Instructions

Strany 2 - Stainless Steel Thru-Hulls

Stainless Steel Thru-Hulls and Scupper ValveInstallation Instructions66540 - 66557, 66576 - 66579 and 67550-67580 SeriesSAVE THESE INSTRUCTIONSForm Nu

Strany 3 - Directives d’installation

Passe-coque et soupape de dalot en acier inoxydableDirectives d’installationSéries 66540 - 66557, 66576 - 66579 et 67550 - 67580CONSERVEZ CES DIRECTIV

Komentáře k této Příručce

Žádné komentáře

Attwood Stainless Steel Scupper Valves Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Hardware Attwood Stainless Steel Scupper Valves. Attwood Stainless Steel Scupper Valves User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Hardware Attwood Stainless Steel Scupper Valves